Model |
CPU224 DC/DC/DC |
Physical characteristic |
|
Dimensions(W x H x D)(mm) |
120.5×80×62 |
Power consume |
7W |
Memory |
Program memory size |
|
With run mode edit |
20K |
Without run mode edit |
20K |
Data memory |
10K |
Back up (by Flash, no need battery) |
keep over 10 years |
I/O |
Local digital inputs |
14 inputs |
Local digital outputs |
10 outputs |
Digital I/O image size |
256(128 inputs/128 outputs) |
Analog I/O image size |
64(32 inputs/32 outputs) |
expansion modules allowed (Max) |
7 modules |
intelligent modules allowed (Max) |
7 modules |
Pulse catch inputs |
14 |
High-speed counters |
6 counters total |
Single phase |
6 at 30KHz |
Two phase |
4 at 20KHz |
Pulse outputs |
2 at 20KHz(DC outputs only) |
General |
Timer |
Total number:256(1ms:4;10ms:16;100ms:236) |
Counters |
256 |
Internal memory bits stored on power down |
256 |
Time interrupts |
2 with1ms resolution |
Edge interrupts |
4 up and/or 4 down |
Analog adjustment |
2 with 8 bit resolution |
Boolean execution speed |
0.08µs per instruction |
Real Time Clock |
Built-in |
Ports |
2 RS-485 ports, within1standard PPI port |
PPI Baud Rates |
9.6,19.2 and 187.5 Kbaud |
Freeport Baud Rates |
1.2kbaud to 115.2Kbaud |
Max. cable length per segment |
With isolated repeater:1000 m up to 187.5kbaud, 1200 m up to 38.4kbaud |
Without isolated repeater: 50 m |
Max. number of stations |
32 per segment, 126 per network |
Max. number of masters |
32 |
Peer to peer(PPI Master Mode) |
Yes |
Power |
Input voltage |
20.4 to 28.8 VDC |
Input current |
110mA while CPU only at 24 VDC |
700mA while Max. load at 24 VDC |
Inrush current |
12A at 28.8 VDC |
Isolation(field to logic) |
Not isolated |
Hold up time(loss of power) |
10ms at 24 VDC |
Sensor voltage |
L+ minus 5 V |
Current limit |
1.5A peak,thermal limit non-destructive |
Ripple noise (sensor to logic) |
Derived from input power |
Isolation (sensor to logic) |
Not isolated |
CPU Digital Input Specifications |
Built-in digital input |
14 |
Input type |
PNP/NPN |
Rated voltage |
24 VDC at 4mA |
Max. continuous permissible voltage |
30 VDC |
Surge voltage |
35 VDC for 0.5s |
Logic "1" voltage range |
15 to 30 VDC |
Logic "0" voltage range |
0 to 5 VDC |
Input delay |
Selectable (0.2 to12.8ms) |
Connection of 2-wire proximity sensor (Bero) |
1mA |
Premissible leakage current (Max.) |
Isolation (field to logic) |
Yes |
Optical galvanic |
500 VAC for 1minute |
Isolation groups |
Refer to Wiring diagram |
High Speed Counter (HSC) input rate |
|
HSC logic level 1(15 TO 30 VDC) |
20K Hz (Single phase), 10K Hz (Tow phase) |
HSC logic level 1(15 TO 26 VDC) |
30K Hz (Single phase), 20K Hz (Tow phase), |
Inputs on simultaneously |
all |
Cable length Max. |
|
Shielded |
500m normal inputs, 50m HSC inputs |
unshielded |
300m normal inputs |
CPU Digital Output Specifications |
Built-in outputs |
10 outputs |
Output type |
Solid State-MOSFET(Sourcing) |
Rated voltage |
24 VDC |
Voltage range |
20.4 to 28.8 VDC |
Surge current (Max.) |
8A for 100ms |
Logic "1" (Min) |
20 VDC,at maximum current |
Logic "0" (Max) |
0.1 VDC with 10KΩ load |
Rated current per point(Max.) |
0.75A |
Rated current per common(Max) |
6A |
Leakage current (Max) |
10µA |
Lamp load (Max) |
5W |
Inductive clamp voltage |
L+ minus 48 VDC, 1w dissipation |
On State resistance (contact) |
0.3Ω Typical(0.6Ω max.) |
Isolation |
|
Optical (galvanic, field to logic) |
500 VAC for 1 minute |
logic to contact |
- |
Resistance (logic to contact) |
- |
Isolation groups |
Refer to wiring diagram |
Delay(Max) |
|
Off to on |
2µs(Q0.0,Q0.1), 15µs(others) |
On to off |
10µs(Q0.0,Q0.1), 130µs(others) |
Switching |
- |
Pulse frequency (Max.) |
20KHz (Q0.0 and Q0.1) |
Lifetime mechanical cycles |
- |
Lifetime contacts |
- |
Outputs on simultaneously |
All at 60℃(horizontal) |
All at 50℃ (Vertical) |
Connecting two outputs in parallel |
Yes, only outputs in same group |
Cable Length (Shielded) |
500m |
Cable Length (unshielded) |
150m |
Order number |
UN 214-1AD23-0XB0 |